Excellent Advantages of new planetary concrete mixer

<p>Troubleshooting III: concrete mixer gearboxes serious noise</p>Henan Daswell Machinery Co., Ltd,is a professional manufacturer and trader specializing in the research, development and production of construction machinery for nearly 30 years. Our main products are as follows:twin shaft compulsory concrete mixer,<a href="http://www.daswellmachinery.com">concrete batching plant</a>s,concrete mixer,blocking making machine,concrete pump,etc. <p> <p>Cause: 1 box of a foreign body, this time need to clear foreign body, the damaged parts repaired or new ones; 2 bearing damage <a href="http://www.beton-mixer.com/products/concrete-mixer/sicoma-meo-twin-shaft-concrete-mixer.html">SICOMA Twin-shaft Concrete Mixer</a>, then we need to replace the bearings;.</p> <p>Troubleshooting four: concrete mixer gearbox overheating</p> <p>Cause: 1 oil viscosity is too high or too low, then the need to release the oil, add new oil; 2 bearing damage, then we need to replace bearings;.</p> <p>Five common faults: Concrete mixer mixing tank temperature is too high ends of the shaft</p> <p>Cause: 1 bearing damage, then you need to replace the bearings; 2 less than the amount o<p>7. ready storage container, placed near the pumps, the suction valve into the container. Water should be used to keep clean;</p>Henan Daswell Machinery Co., Ltd,is a professional manufacturer and trader specializing in the research, development and production of construction machinery for nearly 30 years. Our main products are as follows:<a href="http://www.doubleshaftconcretemixer.com/">concrete mixing plant</a>,<a href="http://www.doubleshaftconcretemixer.com/skipplant/hzs25-skip-type-concrete-mixing-plant.html">concrete batching plant</a>s,concrete mixer,blocking making machine,concrete pump,etc. <p> <p>6. Check the stirred tank, hopper and consistency on the track, such as the wrong direction, the power wiring should be changed;</p> <p>5. Check the rope neatly arranged on the roll, if loose should be re-wrapped well;</p> <p>4. Check all parts of the bolts is solid, especially moving parts of the coupling, if loose should be immediately tightened. Check the open gear together correctly;</p> <p>3. Check the motor wiring and electrical components is solid, reliable power distribution box enclosure must press, all the lines should be properly placed to prevent crushing or bruising caused by accidents at work;</p>f oil, then we need to follow the regulations Annotations lubricants;.</p> <p>Troubleshooting Six: concrete mixer shaft leakage of plasma</p> <p>Failure reasons: 1 floating seal is damaged, then it needs to replace the floating seal.</p>

<p>5. Unscrew the drain plug pump water poured into the water, the water is full of the pump chamber and the suction pipe until it absorbs water so far, then add water and tighten the plug.</p>Henan Daswell Machinery Co., Ltd,is a professional manufacturer and trader specializing in the research, development and production of construction machinery for nearly 30 years. Our main products are as follows:<a href="http://www.beton-mixer.com/products/concrete-mixer/sicoma-meo-twin-shaft-concrete-mixer.html">SICOMA Twin Shafts Forced Concrete Mixer</a>,<a href="http://www.daswellchina.com">concrete batching plant</a>s,concrete mixer,blocking making machine,concrete pump,etc. <p> <p>4. move the pump motor, check the direction of rotation;</p> <p>3. Operation discharge door handle, door opening and closing the discharge should be accurate and in place;</p> <p>2. Start the motor lifting hopper volume field, check the hopper lifting process and upper and lower limit is reliable;</p> <p>1. Start the mixer motor and pulley steering should be consistent with label directions, such as the wrong direction, the power wiring should be changed;</p> <p>Third, concrete mixer load test run</p>